#
# olsr.org OLSR daemon config file
#
# Lines starting with a # are discarded
#
# This file was shipped with olsrd 0.X.X
#

# Debug level(0-9)
# If set to 0 the daemon runs in the background

DebugLevel	0

# IP version to use (4 or 6)

IpVersion	4

# HNA IPv4 routes
# syntax: netaddr netmask
# Example Internet gateway:
# 0.0.0.0 0.0.0.0

Hna4
{
#   Internet gateway:
#   0.0.0.0      0.0.0.0
#   more entries can be added:
#   192.168.1.0  255.255.255.0
}

# HNA IPv6 routes
# syntax: netaddr prefix
# Example Internet gateway:
Hna6
{
#   Internet gateway:
#   ::              0
#   more entries can be added:
#   fec0:2200:106:: 48
}


# Should olsrd keep on running even if there are
# no interfaces available? This is a good idea
# for a PCMCIA/USB hotswap environment.
# "yes" OR "no"

AllowNoInt	yes

# TOS(type of service) value for
# the IP header of control traffic.
# If not set it will default to 16

#TosValue	16

# The fixed willingness to use(0-7)
# If not set willingness will be calculated
# dynamically based on battery/power status
# if such information is available

#Willingness    	4

# Allow processes like the GUI front-end
# to connect to the daemon.

IpcConnect
{
     # Determines how many simultaneously
     # IPC connections that will be allowed
     # Setting this to 0 disables IPC

     MaxConnections  1

     # By default only 127.0.0.1 is allowed
     # to connect. Here allowed hosts can
     # be added

     Host            127.0.0.1
     #Host            10.0.0.5

     # You can also specify entire net-ranges 
     # that are allowed to connect. Multiple
     # entries are allowed

     #Net             192.168.1.0 255.255.255.0     
}

# Wether to use hysteresis or not
# Hysteresis adds more robustness to the
# link sensing but delays neighbor registration.
# Used by default. 'yes' or 'no'

UseHysteresis	no

# Hysteresis parameters
# Do not alter these unless you know 
# what you are doing!
# Set to auto by default. Allowed
# values are floating point values
# in the interval 0,1
# THR_LOW must always be lower than
# THR_HIGH!!

#HystScaling	0.50
#HystThrHigh	0.80
#HystThrLow	0.30

LinkQualityLevel        2

# Link quality window size
# Defaults to 10

LinkQualityWinSize      10


# Polling rate in seconds(float). 
# Default value 0.05 sec

Pollrate	0.05


# TC redundancy
# Specifies how much neighbor info should
# be sent in TC messages
# Possible values are:
# 0 - only send MPR selectors
# 1 - send MPR selectors and MPRs
# 2 - send all neighbors
#
# defaults to 0

#TcRedundancy	0


#
# MPR coverage
# Specifies how many MPRs a node should
# try select to reach every 2 hop neighbor
#
# Can be set to any integer >0
#
# defaults to 1

#MprCoverage	1


# Olsrd plugins to load
# This must be the absolute path to the file
# or the loader will use the following scheme:
# - Try the paths in the LD_LIBRARY_PATH 
#   environment variable.
# - The list of libraries cached in /etc/ld.so.cache
# - /lib, followed by /usr/lib

# Example plugin entry with parameters:

#LoadPlugin "olsrd_dyn_gw.so"
#{
    # how often to check for Internet connectivity
    # defaults to 5 secs
#   PlParam     "Interval"   "40"
    
    # if one or more IPv4 addresses are given, do a ping on these in
    # descending order to validate that there is not only an entry in
    # routing table, but also a real internet connection. If any of
    # these addresses could be pinged successfully, the test was
    # succesful, i.e. if the ping on the 1st address was successful,the
    # 2nd won't be pinged
#   PlParam     "Ping"       "192.168.6.1"
#   PlParam     "Ping"       "194.25.2.129"
#}

LoadPlugin "olsrd_httpinfo.so"
{
    PlParam     "port"   "8080"
    PlParam     "Net"    "192.168.1.0 255.255.255.0"
}
LoadPlugin "olsrd_dot_draw.so"
{
    PlParam     "port"   "2005"
    PlParam     "accept" "192.168.1.0 255.255.255.0"
}


# Interfaces and their rules
# Omitted options will be set to the
# default values. Multiple interfaces
# can be specified.

# !!CHANGE THE INTERFACE LABEL TO MATCH YOUR INTERFACE!!
# (eg. wlan0 or eth1):

Interface "eth2"
{

    # IPv4 broadcast address to use. The
    # one usefull example would be 255.255.255.255
    # If not defined the broadcastaddress
    # every card is configured with is used

    Ip4Broadcast		255.255.255.255

    # IPv6 address scope to use.
    # Must be 'site-local' or 'global'

    # Ip6AddrType		site-local

    # IPv6 multicast address to use when
    # using site-local addresses.
    # If not defined, ff05::15 is used

    # Ip6MulticastSite		ff05::11

    # IPv6 multicast address to use when
    # using global addresses
    # If not defined, ff0e::1 is used

    # Ip6MulticastGlobal	ff0e::1


    # Emission intervals.
    # If not defined, RFC proposed values will
    # be used in most cases.

    # Hello interval in seconds(float)
    # HelloInterval    2.0

    # HELLO validity time
    # HelloValidityTime	6.0

    # TC interval in seconds(float)
    # TcInterval        5.0

    # TC validity time
    # TcValidityTime	15.0

    # MID interval in seconds(float)
    # MidInterval	5.0

    # MID validity time
    # MidValidityTime	15.0

    # HNA interval in seconds(float)
    # HnaInterval	5.0

    # HNA validity time
    # HnaValidityTime 	15.0
}